- BEST WAY TO KEEP LIGHT STRIPS ATTACHED IN CAR INSTALL
- BEST WAY TO KEEP LIGHT STRIPS ATTACHED IN CAR SERIES
Your LEDs will automatically turn on and off in sync with the factory installed lights. Step 6 (Method 2): The benefit of tying your LED system into existing wires for interior car lighting is that no additional fuse or control device is needed.
LEDs will turn on automatically with the vehicle and remain on until cigarette adapter is unplugged or the car is turned off. If you chose not to use a dimmer with wireless remote for control, you will simply need to group all positive leads and all negative leads together, matching polarity to wires from cigarette adapter and using wire nuts to make connections. Repeat these steps to connect the wires from your LEDs to the output of the receiver module. Then retighten screws to make secure connection. If you are using a dimmer with wireless remote, loosen the screws for the input terminals, match polarity and insert stripped cable into the power side of the receiver module. Step 6 (Method 1): If using a 12V cigarette lighter power adapter, start by cutting off the end connector and stripping the cable back about ¼”, identifying polarity of each wire. Before continuing on to step six be sure that your vehicle is turned off. Step 5: Temporarily mount LED strips in desired locations using scotch or painter’s tape and run wires back to a central location to connect to power as specified below.
BEST WAY TO KEEP LIGHT STRIPS ATTACHED IN CAR SERIES
Strip back cable about ¼”, and taking care to match polarities to LED strip, retighten screws to make connection. (Depending on system requirements, wiring series is often easier to connect to power as you will have fewer cables to deal with.) Step 4: Wire each string of lights together by first loosening the screws on each Tiger Paw® screw terminal. (Learn more about using Tiger Paw® Screw Terminals by clicking here.) Push black tab closed to ensure secure connection. Step 3: Add tiger paw screw terminal connectors to the end of each LED strip by peeling back flex strip adhesive, pulling open black tiger paw tab and inserting flex strip. Cut strips to length on copper solder pads only (cutting elsewhere will damage LEDs). Step 2: Measure the available space for each light strip, leaving at least 1.5” of space in any location which will require a cable connection. A sample lighting plan is illustrated below. Common locations for LED accent lighting in cars include under the dash, under seats, and in the trunk. Depending upon where you decide to add your lights, your design will vary. In-line fuse holder with appropriately sized fuse (similar to this one available on Amazon).Method 3- powering directly from car battery
Method 2- powering from existing vehicle light
This project should be completed by qualified and experienced individuals only. Be sure to check your state traffic laws and motor vehicle codes for restrictions on colors and locations of LED lights before installing.
BEST WAY TO KEEP LIGHT STRIPS ATTACHED IN CAR INSTALL
Using this tutorial, and a few basic components, we’ll walk you through several different techniques which can be used to install LED strip lights in your vehicle.ĭisclaimer: Before beginning, please note that laws regarding aftermarket lighting will vary from state to state, however in general, exterior vehicle lighting is prohibited under normal driving conditions. Well, the good news is, it’s not as difficult as it sounds, since most car batteries output 12 volts, and this just happens to be the power requirement for most of Inspired LED’s strip light products. Of course, there is also an aesthetic element to installing LEDs on your vehicle. Exterior car lighting, or under-lighting can make a bold visual statement, sure to make your ride to stand out in a crowd.īut how exactly does one install an LED system in the car when there is no standard outlet to be found? This is a question commonly asked of our Design Team. If you’re an avid camper or frequent road trip adventurer, it can serve as a way to perform tasks a bit more easily than you might under the dim light of your car’s standard fixtures. Interior car lighting can provide a functional element in the ability to find things late at night. While LED lighting is most commonly used around the house, under cabinets or lighting up commercial displays, there are many other creative and unique places where these handy little lights can find themselves at home! One of the less common, but more impressive areas where our LEDs have been utilized is as accent lighting on vehicles.